Gear Meters
Gear meters specifically spur gear, are ideal for low flow rates, viscous fluids, and measurement of flows involving starts and stops or pulsing.
| Items |
 VCB-05-B Flowstat Turbine Flow Sensor List Price $703.00
|
CCB-05-B Flowstat Turbine Flow Sensor List Price $814.00
|
CCB-06-B Flowstat Turbine Flow Sensor List Price $814.00
|
CCB-10-B Flowstat Turbine Flow Sensor List Price $814.00
|
CCB-10-B-C Flowstat Turbine Flow Sensor List Price $814.00
|
|||||
| Manufacturer Name | AW-Lake Company | |||||||||
| Type | Flowstat 5GPM Meter | Flowstat 5GPM Meter | Flowstat 6GPM Meter | Flowstat 10GPM Meter | Flowstat 10GPM Meter | |||||
| Style | ||||||||||
| Output | Voltage | Current | Current | Current | Current | |||||
| Port Size Range | 1/2" NPT | |||||||||
| Medium | Fluid | |||||||||
| Measuring Accuracy | ±2% of full scale | |||||||||
| Repeatability | ±0.5% of full-scale | |||||||||
| Flow Rate | 5 gpm | 5 gpm | 6 gpm | 10 gpm | 10 gpm | |||||
| Turn Down Ratio | 10:1 | |||||||||
| Fluid Temperature Range | 20-225°F (-7° to 107°) | |||||||||
| Maximum Operating Pressure | 14 bar200 psi | |||||||||
| Filtration Requirements | 150 Micron Filter recommended | |||||||||
| Standard Calibration Fluid | Water at 70°F Temperature (21°C), 1.0 sg | |||||||||
| Options | None | None | None | None | Control Cover | |||||
| Casing Material | Stainless Steel 316 | |||||||||
| Cover Material | Clear polycarbonate | |||||||||
| Seal Material | Buna-N® | |||||||||
| Impeller Material | Acetal Copolymer | |||||||||
| Bearing Material | PEEK (Polyetheretherketone) | |||||||||
| Shaft Material | 316 Stainless Steel | |||||||||
| Encapsulant Material | Epoxy | |||||||||
| Strain Relief Material | Nylon | |||||||||
| Lock Ring Material | Stainless Steel | |||||||||
| Wire Insulation Material | High-Temperature PVC | |||||||||
| Power Requirements | 12-24 VDC, Regulated | 12-24 VDC, Regulated, Loop powered | 12-24 VDC, Regulated, Loop powered | 12-24 VDC, Regulated, Loop powered | 12-24 VDC, Regulated, Loop powered | |||||
| Load Driving Capacity | Use the following equation to calculate maximum load resistance: Max Loop Load (Ω) = 50 (Power supply volts – 12). | Use the following equation to calculate maximum load resistance: Max Loop Load (Ω) = 50 (Power supply volts – 12). | Use the following equation to calculate maximum load resistance: Max Loop Load (Ω) = 50 (Power supply volts – 12). | Use the following equation to calculate maximum load resistance: Max Loop Load (Ω) = 50 (Power supply volts – 12). | ||||||
| Maximum Current | 25 mA DC, Regulated | |||||||||
| Minimum Load resistance | 1000 Ω | |||||||||
| Maximum Transmission Distance | 200 feet recommended | |||||||||
| Resolution | Infinite | |||||||||
| Response Time | < 5 seconds to 90% (step change) | 2 seconds to 90% (step change) | 2 seconds to 90% (step change) | 2 seconds to 90% (step change) | 2 seconds to 90% (step change) | |||||
| Over-current limit | Self limiting at 35 mA | Self limiting at 35 mA | Self limiting at 35 mA | Self limiting at 35 mA | ||||||
| Other protection | Reverse polarity | Reverse polarity | Reverse polarity | Reverse polarity | ||||||
| Protection | ||||||||||
| K-Factor | ||||||||||
| Switch Contact | ||||||||||
| Set Point Repeatability | ||||||||||
| A | 1.94 in49 mm | |||||||||
| B | 1.13 in29 mm | |||||||||
| C | 2.00 in51 mm | |||||||||
| D | 2.45 in62 mm | |||||||||
| E | 3.70 in94 mm | |||||||||
| F | 2.63 in67 mm | |||||||||
|
Choice of Three Port Sizes Encapsulated Circuitry Several Outputs Available Connects Directly to your Flow Monitoring Instruments Simply Plumb and Apply Power |
||||||||||
|
|
||||||||||
